Your Plumbing Crash Course: A Guide to Bathtub Installation
Your Plumbing Crash Course: A Guide to Bathtub Installation
Blog Article
They are making a few good observations on the subject of A Step-by-Step Guide to Installing a Bathtub overall in this content below.
Setting up a bathtub isn't precisely rocket science, yet it does need solid plumbing, woodworking, and also often, tiling skills. Replacing an old bath tub with a new one is likewise a moderately difficult job. If the old bathtub is easily available, the task can move immediately; if you have to open a wall to get rid of the old tub and also position the brand-new bath tub, the job is a lot harder. In either situation, the project is within a residence handyman's skills, although you will certainly require an assistant to vacate the old tub and also set in the brand-new one. Make sure you have certified yourself for the work as well as fit attempting it. As opposed to hiring a specialist to take over a halfway-completed project, it is much better to think about employing one before you begin. Opportunities are you may need a specialist plumber to make tube links.
This write-up will help you mount a new bath tub in your restroom if you have actually already bought a new tub as well as do not need to change the arrangement of your previous water pipes.
Your tools as well as product list must comprise the following:
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your installment, then the first thing you ought to do is detach the water. After doing so, activate the faucets to drain any water staying in the system. The process of eliminating the existing faucets can be quite problematic because of the restricted gain access to that is usually the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the faucets. Have a fabric prepared for the remaining water that will certainly originate from the pipelines. As soon as the supply pipelines have been eliminated, make use of the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary faucets from turning throughout this process. When the faucets have been gotten rid of, the holes in the bath/basin will have to be cleaned of any type of old securing substance.
Before going on to fit the new taps, contrast the pipeline connections on the old taps to the new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Fitting New Taps
If the tails of the new taps are plastic, then you will require a plastic connector to stop damage to the thread. One end of the port fits on the plastic tail of the faucet and also the other end offers a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly call for reducing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, position the tap in the mounting opening in the bath/basin making certain that the washing machines are in area in between the tap and also the sink. Protect the faucet in position with the manufacturer given backnut. When the faucet is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal tap connectors. The previous type must be linked to the faucet ends first, tightening up just by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Installing the Tub
Utilizing both wood boards under its feet, position the bathtub in the required position. The wooden boards are practical in equally spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The next goal is to guarantee that the bathtub is leveled all round. This can be achieved by examining the level as well as adjusting the feet on the bathtub till the level reads degree.
To install taps, fit all-time low of the furthest flexible faucet port to the suitable supply pipe by making a compression sign up with; then do the very same for the other faucet.
Turn on the water supply and also check all joints and also new pipework for leakages and tighten them if essential. Fill the tub as well as likewise examine the overflow outlet as well as the regular outlet for leaks.
Lastly, deal with the bath paneling as explained in the maker's user's manual. Tiling and sealing around the tub must wait until the bath tub has been used a minimum of when as this will certainly resolve it into its last placement.
Preparing for the Installation
First of all, the supporting frame supplied with the bathroom needs to be fitted (if called for) according to the supplier's guidelines. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is very important to ensure that if the tap features a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bath, it is also practical to fit a supporting plate under the taps system to prevent pressure on the bathtub.
Fit the versatile faucet connectors to the bottom of the two faucets utilizing 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet through the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you make use of every one of the provided washing machines.
Attach the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom ought to now prepare to be fitted in its final placement.
Tiling Around the Tub
In the area where the bathroom satisfies the tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the installation can move enough to crack a stiff seal, causing the water to pass through the wall in between the bathroom and the tiling, causing issues with wetness and feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your fixtures and also fittings. They are marketed in tubes and cartridges, and also are capable of sealing voids up to a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of soaked paper or soft rope. Bear in mind to constantly load the bathtub with water prior to sealing, to allow for the activity experienced when the tub is in usage. The sealant can crack rather early if you do not consider this movement prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently readily available on the market. It is recommended to fit the tiles making use of water-resistant or waterproof glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a passionate reader about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I assumed sharing that piece of content was sensible. Are you aware of another person who is truly interested in the niche? Do not hesitate to promote it. Thanks a lot for your time. Kindly come by our blog back soon.
Need urgent plumbing repairs? Call. Report this page